Astro Cam Rehab

All to often a mishap occurs and a rocket gets damaged. Find simple (and not so simple) techniques to get the bird back in the air.
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#11 Re: Astro Cam Rehab

Post by bernomatic »

bernomatic said Feb 13, 2016
Time for a trip to Wally Mart to visit a section I haven't been in for a long while, the infant section. Image

I found a new fangled version of an old friend.

Image

I liked the smaller nipple brush stored in the handle which is just perfect for a BT-5. I'm not so happy with the sponges on the end, but I'm sure they'll disappear after a while and I won't have to worry about unwrapping the wires or pulling them out and loosening half the bristles on the rest of the brush.
Chief Cook -n- bottle washer
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#12 Re: Astro Cam Rehab

Post by bernomatic »

bernomatic said Feb 13, 2016
Well the rim started buckling as I scrubbed the insides (no water, I know I don't have to say that, but...) so time for a little Super Glue around the rim.

Image
Chief Cook -n- bottle washer
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#13 Re: Astro Cam Rehab

Post by bernomatic »

bernomatic said Feb 13, 2016
Next straightening the edge by removing about an 1/8th of an inch.
trimming body tube.jpg
trimming body tube.jpg (271.97 KiB) Viewed 7107 times
Last edited by bernomatic on Sun, 24 Sep 17, 01:46 am, edited 1 time in total.
Reason: Photo Bucket Picture Replacement
Chief Cook -n- bottle washer
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#14 Re: Astro Cam Rehab

Post by bernomatic »

I revved this thread not just for a trip down memory lane, and not just because I am ready to continue with the repairs, but because the next step is the fin repair which I will be cutting out of styrene. "Huh? :? so?" you say. Well the styrene is white and the fin can is black. "yeah so??????" So, in another thread I have been looking at airbrushing with a particularly problematic paint. This will be a good project to test out some new information I found on using that paint, Createx airbrush colors. :roll: :ugeek:
Chief Cook -n- bottle washer
User avatar
Commander
Space Captain
Space Captain
Posts: 777
Joined: Wed, 30 Mar 16, 01:49 am
Location: On the Starport

#15 Re: Astro Cam Rehab

Post by Commander »

The project is on hold right now, although I have cut out the fin and prepped it for airbrushing. I purchased a dehumidifier this past Memorial Day and am trying to get the humidity in the basement down below at least 50% before beginning to spray. Yes I do have a moisture trap on the air line, but I think it will be better all around if it's not as damp down there.
Commander
Starport Sagitta
NAR No.97971
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#16 Re: Astro Cam Rehab

Post by bernomatic »

P6090002.JPG
P6090002.JPG (49.12 KiB) Viewed 7925 times
Here is the fin I cut out of sheet styrene, I added a 4 mm tab to the profile copied from the other fins. The sheet stock was a little too thick, so I sanded and shaped the profile to match the existing fins as best I could.
Chief Cook -n- bottle washer
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#17 Re: Astro Cam Rehab

Post by bernomatic »

Using an angle iron and x-acto knife I scribed a line along the fin can where the original fin had been. Than using the x-acto knife, I kept going over the scribe line till I had cut a slot in the fin can. Using sandpaper I widened the hole till the tab from the fin fit like a glove.
P6110005.JPG
P6110005.JPG (147.21 KiB) Viewed 7925 times
P6110010.JPG
P6110010.JPG (78.68 KiB) Viewed 7925 times
Chief Cook -n- bottle washer
User avatar
luke strawwalker
Space Admiral
Space Admiral
Posts: 1535
Joined: Thu, 07 Apr 16, 04:45 am

#18 Re: Astro Cam Rehab

Post by luke strawwalker »

Nice! OL J R
My MUNIFICENCE is BOUNDLESS, Mr. Bond...
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#19 Re: Astro Cam Rehab

Post by bernomatic »

I was getting ready to put this one to bed, when last night during one of the coats using the Createx Air Brush Colors, I was curing the paint on the fin can, when one of the other fins which had long ago broken off and was glued back on, fell off. :twisted: The heat needed to cure the paint had heated the tube type plastic glue enough to allow the bond to be broken.

Of course gluing it back on is possible, but it has ruined the finish of the paint which was looking pretty good. :x :evil: :twisted:
Chief Cook -n- bottle washer
User avatar
bernomatic
Site Admin
Site Admin
Posts: 1167
Joined: Tue, 29 Mar 16, 03:55 am
Location: Cleveland, Ohio
Contact:

#20 Re: Astro Cam Rehab

Post by bernomatic »

I used Rust-oleum filler & primer to prep the fin can
Astro-Cam fin can priimered.JPG
Astro-Cam fin can priimered.JPG (124.82 KiB) Viewed 7911 times
Then I gave it three coats of the Createx/Future Shine 1:1 mixture. Everything was looking fine, the finish almost a semi-gloss.

I glued the fin back on, but it seems very weak. In this picture, the bad fin is the closer upper fin and the replaced fin is the upper away fin, which I noticed has a slight scratch in it, probably from my handling while replacing the re-broken fin.
Astro-Can painted fin can.JPG
Astro-Can painted fin can.JPG (59.37 KiB) Viewed 7911 times
The game plan at this point is to:

1) lightly buff out the scratch with a Q-tip dipped in alcohol. Sanding is NOT recommended with Createx airbrush colors, even if cured. The alcohol will thin and even "erase" the paint job.
2) Spray the undamaged parts with Rust-oleum Crystal Clear Enamel. They need protecting before more scratches appear.
3) Evaluate the fin for repair or replacement.
Chief Cook -n- bottle washer
Post Reply